Micro Hydro Turbine Vertical Tubular Turbine Unit GD-LZ-20-6KW

6kw hydro turbine

Model No:GD-LZ-20-6KW
Output/Power:6 kw
Rated Head:7 Meters
Rated Flow:156 (l/s)
Main Parameters of 6kw Micro Hydro Turbine Generator
No.ItemsParametersRemarks
1ModelGD-LZ-20-6KWVertical

Tubular Turbine

2Rated Head7(meters)
3Rated Flow156(l/s)
4Output6000(W)
5Efficiency60(%)
6Pipe Diameter300(mm)
Generator
No.ItemsParametersRemarks
1ModelSF6.0-4 Permanent Magnet Generator
2StylePMG
3Output6000(W)
4Voltage230 or 110(V)
5Current26.08(A)
6Frequency50 or 60(HZ)
7Rotary Speed1800(RPM)
8PhaseSingle(Phase)
9Power Factor1.0
10Altitude≤3000(meters)
11Insulation GradeB / B
12Protection GradeIP44
13Temperature-25~+50
14Relative Humidity≤90%
Control Box / Control Panel
No.ItemsParametersRemarks
1ModelWY6.0-1 
2Safety ProtectionShort circuit Protection
3Insulation Protection
4Over Load Protection
5Grounding Fault Protection
Packing
No.ItemsParametersRemarks
1Packing MaterialFiberboard 
2Packing Size130×65×88 65×45×38(CM)
4Gross Weight300(KGS)

If you are looking for 6kw Micro Hydro Turbine Generator suppliers in China, you’ve come to the right site.

NO.NamePictureQuantityG.S.
1Micro-hydro Turbine Generator unitMicro-hydro Turbine Generator unit1Set
2Butterfly ValveButterfly Valve1Set
3Reducer PipeReducer Pipe1Set
4Expansion BendExpansion Bend1Set
5Load for Constant Voltage RegulatorLoad for Constant Voltage Regulator1Set
6Asbestos PadAsbestos Pad2Set
7Foot ScrewFoot Screw4Set
8Butterfly Valve ScrewButterfly Valve Screw8Set
9Expansion Bend ScrewExpansion Bend Screw8Set
10Grease lubricantGrease lubricant1Set
11CertificationCertification1Copy
12English Version User Guide1Copy
13Installation Dimension Chart 1Copy

1 Overview

This tubular turbine generator unit is applicable to the low-head power station which has a head of less than 20m and the diameter of runner is less than 3m. With the merits of considerable and well-going flow, and high efficiency, this unit is perfectly suitable for developing water resources of low head and large flow in the areas of plains, hills and Coastal place.

2 Structural characteristics:

The feature of this tubular turbine generator unit is that, the turbine is installed in a “s” type flow pipe, and the axis of turbine pierce through the pipe wall then connect with the generator installed outside the pipe. Between the turbine and generator there can be easily installed a accelerator to make the turbine’s speed out of the constraint on the synchronous speed. The guide vanes and runner have the same characteristics as that of the bulb tubular turbine. Its overall layout is diverse and is up to the unit’s size, capacity and the specific circumstances of hydropower stations. For example, generators can be installed in the upstream side of turbine (front axle stretch), and also can be installed in the downstream side (rear axle stretch); Unit’s axis can be level (level axle stretch) or tilted (tilted axle stretch); Flow Road “S” curve can be both vertical and level, it may also be tilted. The most representative of them is the level rear axle stretch form (generators horizontally installed above the draft tube downstream-side of the turbine). This unit has several merits: can be used for large-scale units, the total flow road is shorter than the front axle stretch style, generator has a high installation elevation, and operating and maintaining are convenient. The drawback: draft tube flow bend a lot, partial loss of the hydropower has some influence on efficiency of the unit; Runner installed with a higher elevation so that there is a constraint on the air performance and the crew of flow; Layout for generators, sufficient distance is necessary between the axis and the top of the draft tube.

3 Performance features:

High specific speed, largest flow and high efficiency, low investment and so on. Compared with the traditional vertical axial units, it has simple structure and larger volume of cross flow, less construction works is needed of and the maintaining is easy as well. With the same capacity, tubular turbine unit has a runner of which the diameter is smaller than the axial tubular unit by 10%-15%, the annual generating capacity is larger by 10%-15%, and the investment costs can be saved than axial of about 20%, its economic benefits is significant.

Local Team Installation Support

Listen to what Our Clients Say

Request a Quick Quote