Site information:
1.head : up to 80m
2.flow: up to 200L/s
3.power 3kW
other requirements
a. flow changes winter / summer….I expect only 80L/s in summer, so system must be flexible in this range
b. distance to load is about 500m, so transmission voltage is important to minimize cost
c. load is a water heater for house. this is thermostat controlled so there will be another ‘dump’ heater needed
Design model: XJ80-3DCT4-Z
————————————————————————
Hello my name is XXX, I have a guest ranch in Baja California, Mexico. We are currently using a 25 kva diesel generator and i am looking to reduce my monthly diesel cost. We have a small stream that runs year round. it has a flow of about 24 gps and 200 ft of head. I would like to get pricing on your XJ38-30SCTF4/6-Z and your XJ38-20SCTF4/6-Z. Thank you in advance for your responce.
Design model:XJ61-30SCTF4-Z
————————————————————————
Dear Sir,
I would like a budgetary quote (>1 year in the future) for the following
application:
Water head: ~50m
Water flow: 10-50 l/s (depending on season)
It must be a 400V 3-phase system
I would like it to be grid-connected in Austria. How do you regulate the
output power etc. depending on waterflow?
I would also like drawing of the complete turbine and detailed drawings
of the inlet and outlet flange, so that we can design also the fittings
for this.
I attach photos for your reference. My plan is to install a pipe for the
whole length of the head. If you have any suggestions of the design for
the inlet of the pipe I would gladly take your advice on this.
I would also like to know what type of gears you use for the suggested
turbine and if maintenance is required for gears or any other parts.
Finally, I will be travelling to Shanghai in May and wonder if I could
visit your factory then?
Design model: XJ2B50-LS-20-SYB-15.0/4
————————————————————————
Head: 7m
Flow: 160 l/s
——————————————————–
Turbine Model: GD-LZ-20-6KW (Vertical Tubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF6.0/4
Output:6KW (Rear Earth Permanent Magnet Synchronous Generator)
Runner Diameter：200mm
Voltage:115V/230VAC in-grid /1 Phase
FQCY:60Hz
Pipe Diameter:300mm (Inside Diameter)
Head:3m
Flow:200 l/s
——————————————————————-
Turbine Model: GD-LZ-25-3KW (Vertical Tubular Turbine)
Rotational Speed:800r/min (Directly Drive)
Generator Model:SF3.0/6
Output:3KW
Runner Diameter：250mm
Voltage:230VAC stand-alone / 1 Phase
FQCY:50Hz
Pipe Diameter:450mm (Inside Diameter)
————————————————————-
Head:6m
Flow:100 l/s
——————————————————————-
Turbine Model: GD-LZ-15-6KW (Vertical Tubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF6.0/4
Output:6KW
Runner Diameter：150mm
Voltage:230VAC stand-alone / 1 Phase
FQCY:50Hz
Pipe Diameter:350mm (Inside Diameter)
——————————————————————-
Head:6m
Flow:150-200 l/s
——————————————————————-
Turbine Model: GD-LZ-20-6KW (Vertical Tubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF6.0/4
Output:6KW
Runner Diameter：200mm
Voltage:230VAC stand-alone / 1 Phase
FQCY:50Hz
Pipe Diameter:450mm (Inside Diameter)
—————————————————————-
Head:12m
Flow:250 l/s
——————————————————————-
Turbine Model: GD-LZ-20-15KW (Vertical Tubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF15/4
Output:15KW
Runner Diameter：200mm
Voltage:230VAC stand-alone / 1 Phase
FQCY:50Hz
Pipe Diameter:450mm (Inside Diameter)
————————————————————————
Head:14m
Flow:25 l/s
——————————————————————-
Turbine Model: XJ25-1.5DCTH4-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF1.5/4
Output:1.5KW
Voltage:230VAC stand-alone / 1 Phase
FQCY:50Hz
Pipe Diameter:125mm (Inside Diameter)
—————————————————————–
Head:30m
Flow:100 l/s
——————————————————————-
Turbine Model: XJ30-15SCTF4/6-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF15/4
Output:15KW
Voltage:230VAC stand-alone / 3 Phase
FQCY:50Hz
Pipe Diameter:250mm (Inside Diameter)
————————————————————————-
Head:100m
Flow:30 l/s
————————————————————————–
Turbine Model: XJ30-15SCTF4/6-Z (Adjustable Dual Nozzles Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF15/4
Output:15KW
Voltage:230VAC stand-alone / 3 Phase
FQCY:50Hz
Pipe Diameter:250mm (Inside Diameter)
Head: 11m
Flow: 45 l/s
——————————————————–
Turbine Model: GD-LZ-12-3.0KW (Vertical Tubular Turbine)
Generator Model:SF3.0/4
Output:3KW
Voltage:230VAC in-grid / 3 Phase
FQCY:50Hz
Pipe Diameter:150mm (Inside Diameter)
Size: 105×56×59 cm
Gross Weight: 126kgs
Head: 6m
Flow: 50 l/s
——————————————————–
Turbine Model: GD-LZ-12-1.5KW (Vertical Tubular Turbine)
Generator Model:SF1.5/4
Output:1.5KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Pipe Diameter:150mm (Inside Diameter)
Size: 95×56×43 CM
Gross Weight: 112kgs
Head:6m
Flow: 389 l/s
——————————————————————-
Turbine Model: GD-WZ-30-15KW (Horizontal Tubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF15/4
Output:15KW
Runner Diameter：300mm
Voltage:230VAC stand-alone / 1 Phase
FQCY:50Hz
Head: 4.3m
Flow: 400 l/s
—————————————————————————-
Turbine Model: GD-WZ-35-12KW (Horizontal Tubular Turbine)
Rotational Speed:900r/min (Directly Drive)
Generator Model:SF12/6
Output:12KW (Rear Earth Permanent Magnet Synchronous Generator)
Runner Diameter：350mm
Voltage:230VAC stand-alone /3 Phase
FQCY:50Hz
Turbine Model: XJ28-6.0DCT4/6-Z (Single Nozzles Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF6.0/4
Output:6KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Pipe Diameter:150mm (Inside Diameter)
Size: 88×57×75 cm
Gross Weight: 196kgs
Head: 15 m
Flow: 100 l/s
———————————————————————————
Turbine Model: XJ15-6.0DCTH6-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF6.0/6
Output:6KW (Induction Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Delivery:30 Days
Head: 7 m
Flow: 300 l/s
———————————————————————————————
Turbine Model: GD-LZ-25-12KW (VerticalTubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF12.0/4
Output:12KW (Rear Earth Permanent Magnet Synchronous Generator)
Runner Diameter：250mm
Voltage:400VAC stand-alone /3 Phase
FQCY:50Hz
Delivery: 45 Days
Head: 6.5 m
Flow: 300 l/s
———————————————————————————
Turbine Model: GD-LZ-25-12KW (VerticalTubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF12.0/4
Output:10-11KW (Rear Earth Permanent Magnet Synchronous Generator)
Runner Diameter：250mm
Voltage:120VAC stand-alone /1 Phase
FQCY:60Hz
Delivery: 45 Days
Head: 4 m
Flow: 140 l/s
——————————————————————-
Turbine Model: GD-LZ-20-3KW (Vertical Tubular Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF3.0/6
Output:3KW (Synchronous Generator)
Runner Diameter：200mm
Voltage:120VAC on-grid / 1 Phase
FQCY:60Hz
Delivery:30 Days
Head: 50 m
Flow: 65-70 l/s
————————————————————–
Turbine Model: XJ30-20SCTF4/6-Z (Daul nozzle Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SFW20.0/4
Output:20KW (Rear Earth Permanent Magnet Generator)
Voltage:230VAC / Stand-alone /3 Phase
FQCY:50Hz
Pipe Diameter:200-250mm (Inside Diameter)
Delivery: 30 Days
Head: 30-35 m
Flow: 16 l/s
————————————————————–
Turbine Model: XJ25-3.0DCT4-Z (Single nozzle Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF3.0/4
Output:2.8-3KW (Induction generator)
Voltage:120VAC / Stand-alone /1 Phase
FQCY:60Hz
Delivery: 30 Days
Head: 12 m
Flow: 500 l/s
—————————————————————————————————–
Turbine Model: GD-LZ-30-40KW (Vertical Tubular Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SFW40.0/6
Output:36KW
Runner Diameter：300mm
Voltage:480VAC stand-alone / 3 Phase
FQCY:60Hz
Pipe Diameter:600-650mm (Inside Diameter)
Delivery: 2 months
Head: 3.5 m
Flow: 350-400 l/s
——————————————————————-
Turbine Model: GD-LZ-30-6KW (VerticalTubular Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF6.0/6
Output:6KW (Rear Earth Permanent Magnet Synchronous Generator)
Runner Diameter：300mm
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Delivery: 40 Days
Head: 18-20 m
Flow: 38-50 l/s
———————————————————————————
Turbine Model: XJ28-6.0DCTF4/6-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF6.0/6
Output:6KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Delivery:40 Days
——————————————–
Head: 18-20 m
Flow: 38-50 l/s
———————————————————————————
Turbine Model: XJ28-6.0DCTF4/6-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF6.0/6
Output:6KW (Induction generator)
Voltage:230VAC on-grid /1 Phase
FQCY:50Hz
Delivery:40 Days
Head: 6.5 m
Flow: 300 l/s
———————————————————–
Turbine Model: GD-LZ-25-10KW (VerticalTubular Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF10.0/4
Output:10KW (Rear Earth Permanent Magnet Synchronous Generator)
Runner Diameter：250mm
Voltage:120VAC stand-alone /1 Phase
FQCY:60Hz
Delivery: 60 Days
Head: 12 m
Flow: 26 l/s
———————————————————————————
Turbine Model: XJ25-1.5DCTH4-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF1.5/6
Output:1.5KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Delivery:30 Days
Head: 15 m
Flow: 20 l/s
———————————————————————————
Turbine Model: XJ25-2.0DCTF4-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF2.0/6
Output:2KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Delivery:30 Days
Head: 60 m
Flow: 18 l/s
———————————————————————————
Turbine Model: XJ28-6.0DCT4/6-Z (Single Nozzles Turgo Turbine)
Rotational Speed:1500r/min (Directly Drive)
Generator Model:SF6.0/4
Output:6KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:380VAC on-grid / 3 Phase
FQCY:50Hz
Pipe Diameter:150-200mm (Inside Diameter)
Delivery:50 Days
Head: 20 m
Flow: 50-60 l/s
———————————————————————————
Turbine Model: XJ28-6.0DCTF4/6-Z (Dual Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF6.0/6
Output:6KW (Rear Earth Permanent Magnet Synchronous Generator)
Voltage:240VAC stand-alone /1 Phase
FQCY:60Hz
Delivery:40 Days
Head:20 m
Flow: 300 l/s
——————————————————————-
Turbine Model: HL110-42-55KW
Rotational Speed:750r/min (Directly Drive)
Generator Model:SF55/8
Output:50KW
Voltage:400VAC stand-alone /3 Phase
FQCY:60Hz
Delivery:4 Months
Design Head: 60 m
Design Flow: 10 l/s
———————————————————————————
Turbine Model: XJ25-3.0DCT4-Z (Single Nozzles Turgo Turbine)
Rotational Speed:1000r/min (Directly Drive)
Generator Model:SF3.0/4
Output:3KW (Induction Generator)
Voltage:230VAC stand-alone /1 Phase
FQCY:50Hz
Delivery:30 Days
Head: 36 m
Flow: 220 l/s
———————————————————————————
Turbine Model: H100-42-75KW
Rotational Speed:750r/min
Generator Model:SFW75/8
Output:75KW
Voltage:400VAC stand-alone /3 Phase
FQCY:50Hz
Delivery:3 Months
———————————————————————————
Greetings,
I am in the process of designing a micro hydro unit on Guadalcanal in the Solomon Islands. I have recently discovered your company and wanted to see if it is a project you might have an interest in. The details for the site are as follows. We have about 43 meters of head. The flow can support up 1135 L/min. The penstock is 3, 75mm PE pipes running approx. 350 meters.
If you could provide me full details on your solution that would be great. At a minimum I would like to know the max power that your solution can provide (Watts), voltage level, 3 phase or single, delivery time frame after order, pictures, drawings, price and any other information you can quickly supply.
Please let me know if you need additional information from me.
Regards, Jay
Suneco Design model:XJ43-6.0DCTF4/6-Z
———————————————————————————
I am from Papua New Guinea. I have graduated with a bachelors degree
in Environment Science at the University of Papua New Guinea. I am
more interested in working with the local community and improving
their living standard. Rural electrification is an important area of
development that I am looking at and I believe in such a terrainous
country with very fast flowing streams, hydro electricity is the most
appropriate system to set up.
I have been engaging myself in some community based conservation
projects including mini hydro power. I have big interest in
electricity an have been doing my own research and studies using
online electrical notes and other information source such as dialogues
and books.
I am writing to your office as I believe there is a big market for
products relating to micro-hydro electricity. The target market is the
Local Level Government and village communities, especially the
schools, clinics, and churces. Even individuals who are welloff would
want a set to be built in thier villages. The market is huge as the
bulk of the population do not have access to the main grid. They also
are not close to the road and so refueling of diesel or patrol gensets
is very difficult and costly.
I can make the market grow here as I can communicate the conviniencies
and the benefits of such products to our potential clients. Currently
there is only fuel gensets and solar sets here in Papua New Guinea as
alternative power sources.
———————————————————————————
writing from Caneroon company Africa Solar and Electric Solutions
Cameroon is a country with about 25 millions citizens but only 25% benefit from electricity supply and in order to solve this problem we are involved in solar installations.
However due to relative high cost of Solar equipments they think that better solution can be obtained through hydropowers generators and we are very lucky that Cameroon has the second bigger potential of water head and flow rate in Africa with hundreds of rivers.
our question:
Actually our technicians have not sufficient skills to calculate water head and flow rate on various sites we intend to put into function.
we are not in good position to give you efficient information about our water sites.
———————————————————————————
Allow me to introduce myself, my name is Andrew Robertson former managing director now director of Meridian Options System Support LTD a telephone maintenance company based in London UK with a customer base throughout the UK.
Being all but retired from the telephone business, I moved back to my former home in the county of Angus Scotland where I have developed an interest in renewable-energy. In the eighties I had a small business draining mountains for agricultural purposes and can see that this no longer practiced practice, coupled with my experience there in, and the type of terrain concerned would lend well to the creation of waterways servicing small scale hydro projects.
My telephone company has the manpower resources and back office facilities as well as financial experience to support endeavours in hydro if this direction is chosen.
Being in Scotland that has its own government with limited powers one of their current incentives is community funding for renewable energy projects
What I would like from your company is current pricing for the supply of your turbines and associated equipment pertaining to small scale hydro projects. With this info and after attaining pricing for penstock piping and so on, I can begin to build a financial model to asses’ viability of proceeding with the above.
———————————————————————————
Feedback from customer on Oct 18, 2013.
Hello Sophia,
I finally managed to finished installing power plant. I have been too busy in Ottawa with the Government but I have had a little time lately.
The Generator works very well. I have tested the generator with a full load it works fine.
I do believe there is a very large market for micro hydro generators in British Columbia. I have been discussing with the provincial government for a simplified process to get water rights for micro hydro.
I have attached a few photos of the powerplant as well as the control box.
I look forward to your reply
Gary
Canada Privy Council
